Aeroquip - 2807 PTFE Hose
Vendor: Aeroquip
Category: Special Application
Application:
SAE 100R14A
Hot air, steam, compressor discharge and most chemical applications. Not recommended for steam-cold water cycling.
Tube:
Extruded PTFE tube
Cover:
Stainless steel single wire braid
Temperature:
–100°F to +500°F (–73°C to +260°C).
Couplings:
Contact JGB for proper fitting recommendation and coupling procedure.
Part Number | Hose I.D. | Hose O.D. | Maximum Operating Pressure |
Minimum Burst Pressure |
Minimum Bend Radius |
Vacuum Service |
Weight of Hose |
Request a Quote | |||||||
mm | in | mm | in | bar | psi | bar | psi | mm | in | kPa | in/Hg | Kg/m | lbs/ft | ||
2807-3 | 3,6 | 0.14 | 6,4 | 0.25 | 210,0 | 3000 | 840,0 | 12000 | 38,1 | 1.50 | 94,8 | 28 | 0,06 | 0.04 | Request Quote |
2807-4 | 4,8 | 0.19 | 7,6 | 0.30 | 210,0 | 3000 | 840,0 | 12000 | 50,8 | 2.00 | 94,8 | 28 | 0,09 | 0.06 | Request Quote |
2807-5 | 6,6 | 0.26 | 9,4 | 0.37 | 210,0 | 3000 | 840,0 | 12000 | 76,2 | 3.00 | 94,8 | 28 | 0,12 | 0.08 | Request Quote |
2807-6 | 8,1 | 0.32 | 10,9 | 0.43 | 175,0 | 2500 | 700,0 | 10000 | 101,6 | 4.00 | 94,8‡ | 28‡ | 0,15 | 0.10 | Request Quote |
2807-8 | 10,7 | 0.42 | 13,7 | 0.54 | 140,0 | 2000 | 560,0 | 8000 | 133,4 | 5.25 | 94,8‡ | 28‡ | 0,18 | 0.12 | Request Quote |
2807-10 | 13,0 | 0.51 | 16,0 | 0.63 | 105,0 | 1500 | 420,0 | 6000 | 165,1 | 6.50 | 94,8‡ | 28‡ | 0,24 | 0.16 | Request Quote |
2807-12 | 16,3 | 0.64 | 19,3 | 0.76 | 84,0 | 1200 | 335,0 | 4800 | 196,9 | 7.75 | 94,8‡ | 28‡ | 0,27 | 0.18 | Request Quote |
2807-16 | 22,4 | 0.88 | 26,2 | 1.03 | 70,0 | 1000 | 280,0 | 4000 | 228,6 | 9.00 | 40,6‡ | 12‡ | 0,39 | 0.26 | Request Quote |
2807-20 | 28,4 | 1.12 | 32,8 | 1.29 | 43,0 | 625 | 175,0 | 2500 | 406,4 | 16.00 | 40,6‡ | 12‡ | 0,51 | 0.34 | Request Quote |
‡ Maximum negative pressure for
-06 and larger are
suitable for hose which has suffered no external damage or
kinking. If greater negative pressures are required for -06 and
larger hoses, the use of an internal support coil is recommended.
Use of an internal support coil in -06 and larger PTFE hose is
recommended for tube support where extended or continuous
service at high temperature together with low or negative pressure is expected.
suitable for hose which has suffered no external damage or
kinking. If greater negative pressures are required for -06 and
larger hoses, the use of an internal support coil is recommended.
Use of an internal support coil in -06 and larger PTFE hose is
recommended for tube support where extended or continuous
service at high temperature together with low or negative pressure is expected.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov |